Description

TOYOTA Yaris Yaris Cross GR Yaris Alphard Vellfire C-HR Harrier 80 series Aqua Sienta Land Cruiser 300 series Drive recorder ETC Accessory power supply Small lamp interlocking Constant power supply 10A 30A Room lamp interlocking Earth Power extraction Optional coupler 13 pin Branch type

point
Continuous power supply (10A), constant power supply (30A), ACC, small lamp interlocking, room lamp interlocking power supply + ground can be obtained with this one!
Just plug in your car’s optional coupler!
An indispensable item for tinkering with electrical equipment!
You can reduce installation costs for ETC, drive recorders, LED illumination products, etc.

Message from the shop
◎It can be used even if you already use the optional coupler!
The coupler of this product is a branch type.
Even if you are already using the optional coupler in your car, you can still use the original device and get additional power by inserting the original coupler into the product’s female connector.

◎The wiring that can be taken out differs depending on the car model!
This product can take out up to 5 types of power sources (continuous power supply (10A), constant power supply (30A), accessory power supply, small lamp interlocking, and room lamp interlocking).
Depending on the type of wiring, you may not be able to extract power from your car.
Before purchasing, please check the wiring that can be extracted from your car using the “Power supply extraction option coupler compatibility table” below.
*BAT (30A), TAIL, and ROOM (-) can only be used on some car models.

◎By using the I-shaped tap, you can easily connect the wiring!
You can easily access the power by simply pinching the included I-shaped tab with pliers!
An indispensable item when installing electrical equipment such as drive recorders, ETC, and LED illumination products!

[Compatible Models]
The product differs depending on the vehicle model and year. Please verify compatibility before purchasing.

[Product Code: TCS-01]
◎ Harrier
Model: MXUA80/85, AXUH80/85
Year: June 2020 onwards
Installation Location: Behind the glove box, upper right
Available Wiring: Accessory power / Ground / Constant power (10A)

◎ Sienta
Model: MXPL10G/15G, MXPC10G
Year: August 2022 – April 2024
Installation Location: Deep inside the passenger-side kick panel
Available Wiring: Accessory power / Interior light linked (-) / Ground / Constant power (10A)

◎ Yaris
Model: MXPH10/15, KSP210
Year: February 2020 – December 2023
*For vehicles updated/facelifted from January 2024 onwards, please use product [TCS-02].
Installation Location: Upper right side (accessible after removing the glove box)
Available Wiring: Accessory power / Parking light linked / Interior light linked (-) / Ground / Constant power (10A/30A)

◎ Yaris Cross
Model: MXPB10/15, MXPJ10/15
Year: August 2020 – December 2023
*Operation has not been verified for vehicles updated/facelifted from January 2024 onwards. Installation location: Upper right side (accessible after removing the glove box)
Available power sources/signals: Accessory power / Parking light (tail light) circuit / Interior light circuit (negative trigger) / Ground / Constant power (10A & 30A)

◎ GR Yaris
Model: GXPA16 / MXPA12
Model year: September 2020 onwards
*Operation has not been verified on vehicles updated/modified from April 2024 onwards. Installation location: Upper right area (accessible after removing the glove box)
Available wiring: Accessory power / Tail light (parking light) linked / Room lamp linked (negative trigger) / Ground / Constant power (10A)

◎ Alphard / Vellfire
Model: AGH30W/35W, GGH30W/35W
Model year: Jan. 2020 – May 2023
Installation location: Upper section of the passenger-side kick panel
Available wiring: Accessory power / Ground / Constant power (10A)

◎ C-HR
Model: NGX10/50, ZYX11
Model year: Nov. 2019 – July 2023
Installation location: Upper section of the passenger-side kick panel
Available wiring: Accessory power / Ground / Constant power (10A)

◎ Aqua
Model: MXPK10/11/15/16
Model year: July 2021 – Present
Installation location: Upper right area (accessible after removing the glove box)
Available wiring: Accessory power / Tail light (parking light) linked / Room lamp linked (negative trigger) / Ground / Constant power (10A, 30A)

◎ Land Cruiser 300 Series
Model: FJA300W/VJA300W
Model year: Aug. 2021 – Present
Installation location: Passenger side, behind the glove box
Available wiring: Accessory power / Tail light linked (ROOM (-)) / Ground / Constant power (10A)
*Note for Land Cruiser 300 Series: The ROOM (-) power output is provided at the location corresponding to the “TAIL” wire on this product. The vehicle-side connector does not have a TAIL wire connection. *Note: BAT (30A), TAIL, and ROOM (-) terminals are compatible with select vehicle models only.

[Product Code: TCS-02]
◎ Yaris
Model: MXPH10/15, MXPH10/14/15/17, KSP210
Model Year: January 2024 onwards
Installation Location: Upper right side (behind the glove box)
Available Power/Signal Lines: Accessory power / Tail light (parking light) linked / Room lamp linked (-) / Ground / Constant power (10A/30A)

*BAT (30A), TAIL, and ROOM (-) can only be used on some car models.

[Product specifications]
– Simply plug it into the optional coupler on the passenger seat to access 5 types of power sources (accessory power, small lamp interlocking, room lamp interlocking (-), constant power (10A, 30A)) + ground.
*There is no need to insert a fuse.
*Please check the shape of the optional coupler near the passenger seat glove box and kick panel of your car before purchasing.
*For the location of the optional coupler, please check the installation location of the compatible vehicle model listed above.

[Product contents]
・Optional coupler (branch type)
・I-shaped tap (electro tap) x 6
*Instruction manuals etc., are not included.

◎A versatile coupler that allows you to take out 5 types of power + ground just by inserting the optional coupler!
◎Easy to install! Just plug it into the optional coupler at the foot of the passenger seat!
◎Uses an I-shaped tap that allows you to quickly branch wiring with pliers!
◎You can save on installation costs for drive recorders, ETC, LED illumination products, etc.!
◎By inserting the coupler that was originally inserted into the female connector of the product, you can get additional power while using the original device!

[How to check with a tester]

●Continuous power supply (BATT 10A/BATT 30A)/+
With the engine OFF, connect a tester to the “BATT 10A” or “BATT 30A” wiring and the product’s GND/- or body ground (-) to check for electricity.

●Accessory power supply (ACC)/+
Press the start button once without stepping on the brake, connect a tester to the “ACC” wiring and body ground (-), and check for electricity.
*Depending on the grade of Sienta, in the initial stage, even if you press the power switch once without stepping on the brake, the ignition may turn on and the ACC state may not be activated.
In that case, if you want to check if the power is on, please turn on the ACC mode setting in the navigation customization settings (ACC customization).

●Small lamp interlocking (TAIL)/+
Turn on the light and connect a tester to the “TAIL” wiring and the product’s GND/- or body ground (-) to check for electricity.

●Room lamp interlocking (ROOM)/- (*Caution minus control)
Open the door with the room lamp switch linked to the opening/closing of the door, and connect a tester to the “BATT/+” wiring and “ROOM” wiring to check for electricity.
*When connecting the clip side of the voltage tester to the “continuous power supply (BATT 10A/BATT 30A)/+”, wrap the entire clip of the voltage tester with insulating tape, etc., so that it is completely insulated so that no metal is exposed. Please. If you touch even the slightest bit of metal on the car body, it may cause a short circuit. If you are concerned, always put a fuse on the power supply side wiring so that the fuse on the car side will not blow even if there is a short circuit.

●GND/-
Please connect a tester to the “GND” wiring and the product’s constant power supply (BATT 10A/BATT 30A)/+ to confirm power supply.

*A tester is not included, so please prepare it yourself.

【Notes】
*BAT (30A), TAIL, and ROOM (-) can only be used on some car models.
*If you take out the power source of BATT 30A/+ and connect it to a large-capacity electrical component, please connect it to the body ground or battery (-) instead of the GND wire (earth) of this product.
*For those who have basic knowledge and know how to install. We cannot provide any installation support.
*Instruction manuals etc. are not included.
*Please note that under no circumstances will we be able to accept returns or exchanges after installation.
*If the wires touch each other, there is a possibility of a short circuit. Wrap unused wires with insulating tape to prevent them from coming into contact with each other to prevent short circuits.
*Please note that there may be small scratches caused during the manufacturing process.
*Please perform installation work at your own risk.