Description

FRONT GRILL [ PAINTED]  – 75,000 yen / [UNPAINTED] – 65,000 yen
For mid-cycle models (September 2013 – August 2017) only
* Made of FRP, white gel coat finish, unpainted
* Compatible with genuine T-mark (Toyota mark) emblem.
* The genuine grille and chrome frame are transplanted from the genuine grille for installation.
* The genuine T-mark (Toyota mark) emblem is also transplanted in the same way.
* A type specifically for vehicles with an optional “front camera” is also available.
* Cannot be installed on vehicles equipped with a pre-collision safety system (millimeter-wave radar).
* The design, which is based on the popular LEXUS GX460 grille from the early model, has been adopted for the mid-cycle model as well. It has been finished with a design that emphasizes a luxurious atmosphere and a wide feel, which is distinctly different from the genuine grille.

RONT BUMPER SPOILER [UNPAINTED] – 195,000 yen
Mid-term model (September 2013 to August 2017) only
・FRP white gel coat finish unpainted product
・For fog lamps, genuine products are diverted.
・Includes 5 LED lamps on one side.
Established a big face that is well-balanced with the wider grille area of the mid-term model. The wing-shaped under spoiler placed on the bottom part is well-balanced and has an overwhelming low form and the effect of making the car look bigger.
Resin mesh is used for the mesh net in the center. Contributing to quality improvement.

REAR BUMPER SPOILER TYPE 2[UNPAINTED]- 240,000 yen
For early/mid-term models
* Late model (September 2017-) cannot be installed
・FRP white gel coat finish unpainted product
・2TR-FE (2.7L), 1GR-FE (4.0L)
Compatible with 1GD-FTV (clean diesel).
・Also compatible with 4.0L TZ-G (rear air suspension vehicle)
・Includes LEXUS LS genuine tailpipe diffuser & stainless steel bypass muffler on both sides. It realizes a double-sided exhaust that is not a dummy.
・Includes a reflector.
・Spare tire can be installed.
*It is necessary to remove the tow hook on the rear side.
Duct-style slits on the sides are based on the conventional rear bumper spoiler. And by making the inside of the LS tail a diffuser shape, it has a sporty design.

LED REFLECTOR – 15,500 yen
By replacing and wiring the genuine reflector, 30% of light is emitted when the small lamp is lit, and 100% of light is emitted when the brake lamp is lit, realizing double lighting of small / brake.
Not only does it dress up the rearview, but it also enhances visibility from the following vehicle and prevents rear-end collisions.
* A genuine bumper can be used
* Compatible with genuine KOITO part number: 53-17601L/R

Rear Half Spoiler FRP [Unpainted] – 229,500 yen / [Without Muffler]  – 105,000 yen
・FRP white gel coat finish unpainted product
・For 2TR-FE (2.7L) and 1GR-FE engines
Compatible with 4.0L TZ-G (rear air suspension vehicle)
・Includes a stainless steel rear piece dual tail muffler that realizes realistic exhaust.
・Spare tire can be installed.
・The rear tow hook needs to be removed.
A half-shaped rear spoiler designed for combination with left and right 4 mufflers. Because the shape does not use the genuine rear reflector, it is possible to achieve a large image change from the normal one even though it is a half shape (exclusive reflector included). The dedicated muffler adopts a standard-type tail with a dual 115mm diameter. Equipped with a tail slide function that can be adjusted to your desired width.
*The product has holes for the rear corner sensor and back sensor. If your vehicle is not equipped with it, please purchase a dummy sonar (sold separately).

Sold separately: LED reflector
By replacing and wiring the genuine reflector, 30% of light is emitted when the small lamp is lit, and 100% of light is emitted when the brake lamp is lit, realizing double lighting of the small / brake. Not only does it dress up the rearview, but it also enhances visibility from the following vehicle and prevents rear-end collisions.

Sold separately: Dummy sonar for rear half spoiler
Dummy sonar for vehicles without genuine optional clearance sonar. Attach it to the service hole of the product body with the attached double-sided tape. *The product is not painted.

Rear Half Spoiler Type X [Unpainted] – 259,500 yen / [Without Muffler]  – 105,000 yen
・FRP white gel coat finish unpainted product
・For 2TR-FE (2.7L) and 1GR-FE engines
Compatible with 4.0L TZ-G (rear air suspension vehicle)
・Includes a stainless steel rear piece dual tail muffler that realizes realistic exhaust.
・Spare tire can be installed.
・The rear tow hook needs to be removed.
A half-shaped rear spoiler designed for combination with left and right 4 mufflers. Because the shape does not use the genuine rear reflector, it is possible to achieve a large image change from the normal one even though it is a half shape (exclusive reflector included). The dedicated muffler adopts a standard-type tail with a dual 115mm diameter. Equipped with a tail slide function that can be adjusted to your desired width.
*The product has holes for the rear corner sensor and back sensor. If your vehicle is not equipped with it, please purchase a dummy sonar (sold separately).

Sold separately: LED reflector
By replacing and wiring the genuine reflector, 30% of light is emitted when the small lamp is lit, and 100% of light is emitted when the brake lamp is lit, realizing double lighting of the small / brake. Not only does it dress up the rearview, but it also enhances visibility from the following vehicle and prevents rear-end collisions.

Sold separately: Dummy sonar for rear half spoiler
Dummy sonar for vehicles without genuine optional clearance sonar. Attach it to the service hole of the product body with the attached double-sided tape. *The product is not painted.

Side Extension [Unpainted] – 70,700 yen
For cars with a genuine option side step cover
・FRP white gel coat finish unpainted product
・Installation uses double-sided tape and screws
An extension part that covers the lower part of the Toyota genuine optional side step cover. The ground clearance is about 45mm lower than the genuine OP side step cover.
Perfect for balancing the side view with the Elford Bumper Spoiler. In addition, it demonstrates a visual lowdown form that does not rely on the use of springs.

20mm over fender for Elford Aero [Unpainted] – 70,500 yen
Mid-term model (September 2013-August 2017)
・FRP gel coat finish unpainted product
・The rear is divided into 2 parts, consisting of a total of 6 pieces.
*Vehicles with genuine OP side molding require the processing of the product (door part).
20mm wide (one side) over the fender for Elford Aero (front and rear). By increasing the wide feeling, it creates a powerful form and emphasizes individuality as an accent to the side view.
* Structural changes are required due to changes in vehicle width.

9mm over fender for Elford Aero [Unpainted] – 64,500 yen
Mid-term model (September 2013 to August 2017) only
・FRP gel coat finish unpainted product
・Rear divided into 2 parts, a total of 6 pieces.
・Compliant with a vehicle inspection.
*Vehicles with genuine OP side molding require the processing of the product (door part).
9mm wide fender for 150 Prado mid-term Elford Aero (front bumper/rear half). The design along the genuine press line realizes a form that does not feel uncomfortable. Accent the side view.

protector lamp stay – 105,500 yen
For the mid-term model (September 2013 to September 2017)
・76.3Φ steel pipe powder coating finish
・Stainless steel skid plate included
・ Number relocation plate included
・Body weight: 11.5 kg
・Fog lamps can be installed up to 200Φ.
*When installing a stone guard with a 200Φ lamp, the guard may interfere.
* For standard (normal) bumper
* Vehicles equipped with clearance sonar will interfere with radio waves, so it is necessary to turn off the operation.
*Vehicles equipped with the genuine OP front camera may greatly block the field of view.
It is a lamp stay that enables the installation of a large lamp that is indispensable for off-road driving.
A stainless steel skid plate is standard equipment at the bottom of the product. Gives the Prado a cross-country feel.

Stealth side step – 95,500 yen
for all cars
・50mm×90mm steel pipe powder coating finish
・Anti-slip rubber included
A thin side step that uses an oval shape.
The oval-shaped pipe has a thickness (height) of only 50 mm, so it does not sacrifice the ground clearance and emphasizes the height of the vehicle. However, the step surface (tread surface) has a depth of 90 mm, which is close to a flat shape, making it easy to put your feet on. In addition, if you use the included anti-slip rubber, you can get on and off easily without slipping even in rainy weather. The main body and mounting stay are finished with a semi-matte black powder coating, making it inconspicuous.
Since a strong steel pipe is used for the material, it also plays a role in protecting the side sill when driving on rough roads.
In addition, the main body has a sliding function, so it is possible to adjust the width according to custom, etc. And the products are made in Japan with the peace of mind that they are manufactured in Japan.
Despite being a tough existence, it erases its presence. It’s a stealthy sidestep.

 
Sonic Art Alloy Wheels – 398,200 yen
The concept of Sonic Art is a “Fusion of performance and beauty of appearance”. By adopting a cover type that has little effect on the design and combining it with the concave shape that is dropped from the outermost circumference of the rim to the center part, it has a spoke shape that is supple and stretches from the center to the rim end. In addition to a sophisticated design such as diamond cutting on the spoke surface, the flow-forming method realizes the ultimate lightness (13.4 kg/piece). Although it is 22 inches in size, it is lighter than the genuine wheel, so it also emphasizes athletic performance. Sonic Art is the “lightest and most powerful wheel for Prado”, which is suitable for calling it art that combines performance and aesthetics.
Size: 22 x 9.5J 6H-139.7 Inset +20
Color: Sonic Black / Diamond Cut Face
Flow forming method
Accessories: Aluminum center cover set, Aluminum black air valve
Standard: JWL, VIA standard-compliant product

Bloodstock 1 piece 2 Alloy Wheels – 398,200 yen
Size: 17 x 8.0J 6H-139.7 Inset ±0
Based on one piece of Bloodstock, it is a model specialized for vehicles with over fenders such as Land Cruiser Prado, FJ Cruiser, and Hilux. Round holes, which are the core of the design, are processed in three dimensions, and milling (cutting) is performed on the edges of window openings and irregularly shaped holes. A method to fix the cap is adopted.
Stronger, clearer, one-size-only evolution model. That is Bloodstock 1 piece 2.
Accessories: Center cap set, air valve
Standards: JWL, JWL-T, VIA standard-compliant product

Matt black/Mill dimple
gloss black/polished rim
Silver polish

Bloodstock 1 piece  Alloy Wheels – 288,200 yen
Size: 17 x 8.0J 6H-139.7 Inset +30
The Bradstock design is based on a round-hole dish design that boasts overwhelmingly high strength performance in terms of rigidity and strength. However, the dish design has disadvantages such as a large disk surface area, increased weight, and poor heat dissipation. Therefore, the design of the bloodstock is different from the conventional round hole dish design in order to eliminate the disadvantages. The round hole, which is the core of the design, has been 3-dimensionally processed to create a unique shape that fuses with the dish and spokes. As a result, by widening the hole opening, the weight increase is suppressed and heat dissipation is improved.
Of course, it’s not about performance, but the unique design of Bradstock creates a beautiful form like no other. Milling (cutting) the edge of the window opening gives it brilliance, giving it both daring and high quality. I believe that Bloodstock has been recognized as a classic design that never goes out of fashion by maintaining a consistent design concept from its birth to the present.
A sense of stability and security because it is a classic. That’s the beauty of Bloodstock.
Accessories: Center cap, air valve
Standards: JWL, JWL-T, VIA standard-compliant product

Matt black/Mill dimple
gloss black/polished rim
Silver polish

Bloodstock 1 piece 2 Alloy Wheels – 288,200 yen
Size: 17 x 8.0J 6H-139.7 Inset ±0
Based on one piece of Bloodstock, it is a model specialized for vehicles with over fenders such as Land Cruiser Prado, FJ Cruiser, and Hilux. Round holes, which are the core of the design, are processed in three dimensions, and milling (cutting) is performed on the edges of window openings and irregularly shaped holes. A method to fix the cap is adopted.
Stronger, clearer, one-size-only evolution model. That is Bloodstock 1 piece 2.
Accessories: Center cap set, air valve
Standards: JWL, JWL-T, VIA standard-compliant product

Matt black/Mill dimple
gloss black/polished rim
Silver polish

Hub-centric wheel spacer – 62,800 yen
30mm thick wheel spacer with integrated hub ring developed exclusively for Toyota vehicles. It has a size setting suitable for aero over fenders.
■ Hub diameter: 106.1mm
■ Made in Japan
■ Nut size: M12 x 1.5
■ Outer diameter: 179.0mm
●Accessories: Penetration nuts 12 x 1.5 24 pieces, adapter
For 1 car: 1 set of 4 sheets